Z-Wave Plus Fibaro Датчик открытия двери/окна
Main features of FIBARO Door/Window Sensor:
- Compatible with any Z-Wave or Z-Wave+ Controller
- Supports protected mode (Z-Wave network security mode) with AES-128 encryption
- Door/window opening detected through separation of Sensor’s body and a magnet
- Easily mounted on doors, windows, garage gates and roller blinds
- Battery powered
- Visual LED indicator signalling status of the device
- Compatible with the DS18B20 temperature sensor
- Potential-free input allowing to connect a button or binary sensor
Door/Window Sensor
Датчик открытия двери/окна с питанием от батареи является Z-Wave совместимыми датчиком. Он сочетает в себе функциональность 3 устройств (датчик открытия/закрытия, бинарный датчик и датчик температуры). Датчик может быть использован для контроля состояния открытия двери, окна, жалюзи или гаражных ворот. Кроме того, вы можете интегрировать любые датчики с бинарным выходом с сетью Z-Wave с помощью этого датчика, например, датчики движения, затопления, сигнализации и т.д.
Датчик состоит из двух элементов. Одна из частей крепится на подвижную часть окна или двери. Другая часть находится на раме.Устройство должно быть включено в Z-Wave сеть с помощью пульта дистанционного управления или любого другого Z-Wave контроллера. В случае обнаружения действия, датчик посылает сигнал в сеть центральному Z-Wave контроллеру.
The Door/window sensor is a battery powered reed sensor. It's operation under the z-wave standard guarantees compatibility with the Fibaro system. The sensor expands the capabilities of the system by monitoring the opening of doors, windows and garage doors. It is used in automatic light control, access control and property protection systems. Installation of the Door / Window Sensor in your home increases the safety and comfort of its inhabitants. It also eliminates the risk of high fees for heating or air conditioning. In addition, the module can be equipped with a temperature sensor, and use the built-in binary input.
Functionalities:
The Door/window sensor combines the functionality of 4 devices:
|
|||
Reed sensor |
Binary input |
Temperature sensor |
Scenes switch |
1) Reed sensor
Installation of reed sensors in your home will provide the HOME CENTER 2 with additional information, which can be used to control other components of the Fibaro system. The module checks the condition of opening / closing any window or door. Opened window will prevent the system from launching heating or air conditioning in a particular room. Therefore, you will not be exposed to unnecessary costs. When mounting reed sensor on the front door, you can turn on the lights automatically when opening the door or run a pre-programmed scene e.g. "Return home". In addition, the Door / Window Sensor can be used as an unauthorized intrusion alarm sensor. These are just some of the capabilities of the Door / Window Sensor.
Applications:
Door & Windows | Garage door |
Gates |
2) Wireless entry sensor
The Door/Window Sensor may be used together with the HOME CENTER 2 to start any feature. Once the Door/Window Sensor input is connected with a typical wall switch it can control other components of the Fibaro system. The idea behind it is to enable the user to place a previously unplanned switch in a chosen location without the necessity to lay cables. The number and location of existing switches no longer limit the arrangement of your interior. The Door/Window Sensor can easily and non-intrusively take up the role of this element of the home electrical system.
3) Temperature sensor
The Door/Window Sensor module also works with the DS18B20 temperature sensor (sold separately). This tiny element is installed in the module inputs and added to the Fibaro system. Its installation is very simple. Simply place three leads in the inputs and secure them using the screws. The temperature sensor can greatly extend the number of features available with the Home Center. The reed sensor feeds the Fibaro system with information about an open window; the temperature sensor can collect the data necessary for automatic ventilation of a room without cooling it excessively. The temperature sensor may also be used during the planning of a temperature profile at the heating panel.
4) Pre programed scenes switch
The Door / Window Sensor has a unique feature can automatically trigger pre programed scences. To start a scene on the level of electric installation was difficult until now. It required a Fibaro module, previously installed in an electric device, which could run a scene. This solution was not intuitive enough. Just to meet that customer expectation we gave the Door / Window Sensor the additional functionality to start scenes. Simply connect a traditional light switch or any sensor (e.g. motion detector) to the FIBARO module and indicate a pre-programmed scene to start. Therefore you gain a universal battery and completely wireless switch of multiple devices ready to work within a short time.
Applications:
Button "leaving home / homecoming" as on/off in the pre-defined devices. |
Connect a traditional switch to the FIBARO module and indicate a pre-programmed scene in HC2 to start. Make a number of clicks on switch an indicator to run a specific scene. |
Switch, which in conjunction with the RFID reader (e.g. car module) will open the gate to the property, raise the door to the garage, start ventilation inside, turn on lights on the driveway and the road to the house, and finally closes the gate. |
Extremely compact
The Door/window Sensor is extremely compact. It is the smallest unit of this type available on the market. Its extremely lightweight and thin design makes it almost invisible on every window and door.
Easy and fast installation
Installation of the module is very simple. Just remove it from the box, open the case, get rid of the protective film on the battery and stick it to the surface with the supplied double-sided mounting tape. Low power consumption reduces battery replacement to 2 years. The system will notify you in advance in case of low power status. Current battery consumption is always visible in HOME CENTER 2 configuration panel.
Intuitive installation
The user-friendly interface ensures an easy and intuitive way of adding devices to Fibaro System. Door / Window Sensor installation is extremely simple. It does not exceed 3 minutes.
Adding sensor to Home Center 2
1) Go to the DEVICES section and click the "Add” button.
2) Home Center 2 will be set to LEARNING MODE.
3) Click the service button at the back of the sensor's casing.
4) Your Fibaro Door/Window Sensor is ready to operate.
Wireless update*
Customized
Чем больше диапазон действия, тем более надежным является продукт - устройство имеет первоклассную антенну. Оптимизированное для надежности, это устройство может взаимодействовать беспроводным способом на расстояния более 150 метров.
Лучше антенна. Лучше Z-Wave. Устройство разработано на технологии Z-Wave Plus последнего 5го поколения, чтобы предоставить вам самое быстрое время отклика и оптимальное время жизни батареи между перезарядками.
Если вы используете устройство для обеспечения безопасности, вы хотите чтобы взаимодействие было защищенным. Вот почему устройство использует беспроводное шифрование AES-128 для защиты от несанкционированного доступа и хакеров.
Используете ли вы устройство для комфорта или безопасности, вы желаете чтобы оно всегда оставалось обновленным до последней версии. Как бы не создавались обновления прошивки для устройства, вы всегда можете обновить его с помощью Microsoft Windows или выбрать Z-Wave контроллер.
Technical Specification
- HARDWARE
- Z-Wave Chip 500 series
- COMMUNICATION PROTOCOLS
- Z-Wave Plus
- Z-WAVE GROUPS
- Five groups and five devices each (nodes)
- DETECTION
- Magnetic
- INPUTS
- Single, potential-free (IN)
- SUPPORTED TEMPERATURE SENSOR
- single, DS18B20
- DIMENSIONS
- Packing size:70x70x40 mm (LxWxH)
- Base size: 76x17x19 mm (LxWxH)
- CERTIFICATIONS
- CE, Z-Wave
- POWER SUPPLY
- Lithium battery, 3.6 V, 500mAh
- POWER CONSUMPTION
- up to 1W
- RADIO SIGNAL POWER
- up to 1mW
- RANGE
- up to 150m (outdoors) and 100m (indoors)
- OPERATIONAL TEMPERATURE
- 0-40°C
- RELATIVE HUMIDITY:
- 8% - 80%.
- IP CODE
- IP20
Package content
- Unit:
- Sensor Unit.
- Magnet Unit (x1).
- Double-Sided Tape(x2).
- Screws (x2).
- User manual
Z-Wave Specification
Z-Wave Association Capabilities
Group ID |
Maximum Nodes |
Description |
1 | 1 | Z-Wave Plus Lifeline. Type of frame sent by the device when the association group is activated: DEVICE_RESET_LOCALLY_NOTIFICATION; NOTIFICATION_REPORT; BATTERY_REPORT; SENSOR_MULTILEVEL_REPORT. |
2 | 5 | Control is assigned to the magnetic sensor and IN input. Opening or closing will result in sending BASIC_SET control command to associated devices. |
3 | 5 | Alarm reports alarms. Alarm frame (SENSOR_ALARM_REPORT) will be sent to associated devices once such an event has been detected. Works ONLY if external sensor connected – unused if Door/Window Sensor selected in parameter 20. |
4 | 5 | Sensor ZW3 is assigned to the magnetic sensor and IN input. Opening or closing will result in sending BASIC_SET control command to associated devices. Group provides backward compatibility with controllers not supporting Z-Wave+. Only such controllers should be added to this group. Type of frame sent by the device when the association group is activated: SENSOR_BINARY_REPORT. |
5 | 5 | Tamper ZW3 is assigned to the tamper alarm. Alarm frame will be send to associated devices once tampering has been detected. Group provides backward compatibility with controllers not supporting Z-Wave+. Only such controllers should be added to this group. Type of frame sent by the device when the association group is activated: SENSOR_ALARM_REPORT. |
Z-Wave Configuration Capabilities
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
1 | 1 | OPERATION MODE | 0 (Default) |
Door/Window Sensor or external alarm sensor (type - see par. 20) | |
1 | External switch | ||||
10 | 1 | 2ND ASSOCIATION GROUP TRIGGERS | 2 | switch after closing | |
0 (Default) |
switch after opening and closing | ||||
1 | switch after opening | ||||
11 | 1 | COMMANDS SENT TO 2ND ASSOCIATION GROUP | 0 | ON | |
1 | OFF | ||||
2 (Default) |
ON and OFF | ||||
12 | 2 | VALUE OF ON COMMAND FRAME SENT TO 2ND ASSOCIATION GROUP | 1 to 99 | Sets an associated device to a specified level. | |
255 (Default) |
Turns ON the device. | ||||
0 | Turns OFF the device. | ||||
13 | 2 | VALUE OF OFF COMMAND FRAME SENT TO 2ND ASSOCIATION GROUP | 0 (Default) |
Turns OFF the device. | |
255 | Turns ON the device. | ||||
1 to 99 | Sets an associated device to a specified level. | ||||
14 | 2 | TIME DELAY OF ON COMMAND FRAME | 0 to 32400 (Default) |
time in seconds, max 9h | |
15 | 2 | TIME DELAY OF OFF COMMAND FRAME | 0 to 32400 (Default) |
time in seconds, max 9h | |
2 | 1 | DOOR/WINDOW/ALARM STATUS | 0 (Default) |
Door/window closed | |
1 | Door/window opened | ||||
20 | 1 | TYPE OF SENT ALARM FRAMES | 0 (Default) |
Door/Window Sensor (General Purpose Alarm) | |
1 | smoke sensor (Smoke Alarm) | ||||
2 | CO detector (CO Alarm) | ||||
3 | CO2 detector (CO2 Alarm) | ||||
4 | high temperature sensor (Heat Alarm) | ||||
5 | flood sensor (Water Alarm) | ||||
3 | 1 | LED INDICATIONS | 0 | no indications | |
1 | indication of opening/closing status change (input IN) | ||||
2 | indication of wake up (1 x click or using time interval) | ||||
4 | indication of device tampering | ||||
30 | 2 | DELAY OF TAMPER ALARM CANCELLATION | 0 to 32400 (Default) |
time in seconds, max 9h | |
31 | 1 | REPORTING TAMPER ALARM CANCELLATION | 0 | Do not send tamper cancellation report | |
1 (Default) |
Send tamper cancellation report | ||||
4 | 1 | RANGE TEST AFTER DOUBLE CLICK | 0 (Default) |
Disabled | |
1 | Enabled | ||||
50 | 2 | INTERVAL OF TEMPERATURE MEASURING | 0 | temperature measurements disabled | |
5 to 32400 (Default) |
time in seconds, 5 seconds - 9 hours | ||||
51 | 2 | TEMPERATURE REPORT THRESHOLD | 0 | temperature reports based on threshold disabled | |
1 to 300 (Default) |
temperature threshold (0.1-30 degrees Celsius, 0.1 degrees step) | ||||
52 | 2 | TEMPERATURE REPORTS INTERVAL | 0 (Default) |
periodic temperature reports disabled | |
5 to 32400 | time in seconds, 5 seconds - 9 hours | ||||
53 | 2 | TEMPERATURE OFFSET | -1000 to 1000 (Default) |
-100 – 100 degrees Celsius, in 0,1 degrees steps | |
54 | 1 | TEMPERATURE ALARM REPORTS | 0 (Default) |
temperature alarms disabled | |
1 | high temperature alarm | ||||
2 | low temperature alarm | ||||
3 | high and low temperature alarms enabled | ||||
55 | 2 | HIGH TEMPERATURE ALARM THRESHOLD | 0 to 1000 (Default) |
0 - 100 degrees Celsius, in 0,1 degrees steps | |
56 | 2 | LOW TEMPERATURE ALARM THRESHOLD | -300 to 700 (Default) |
-30 - 70 degrees Celsius, in 0,1 degrees steps | |
70 | 2 | SCENE ACTIVATION FUNCTIONALITY | 1 | [ID 10] opening door/window (single click) | |
2 | [ID 11] closing door/window (single click) | ||||
4 | [ID 12] holding | ||||
8 | [ID 13] releasing | ||||
16 | [ID 14] double click | ||||
32 | [ID 15] triple click | ||||
256 | [ID 50] high temperature - door/window opened | ||||
512 | [ID 50] high temperature - door/window closed | ||||
1024 | [ID 51] low temperature - door/window opened | ||||
2048 | [ID 51] low temperature - door/window closed | ||||
71 | 1 | ALARM BROADCAST | 0 (Default) |
broadcasts inactive | |
1 | ON/OFF commands broadcast active | ||||
2 | sensor alarm broadcast active | ||||
4 | sensor alarm broadcast active | ||||
72 | 1 | ASSOCIATIONS IN Z-WAVE NETWORK SECURITY MODE | 0 | none of the groups sent as secure | |
1 | 2nd group, Control, sent as secure | ||||
2 | 3rd group, Alarm, sent as secure | ||||
4 | 4th group, Sensor ZW3, sent as secure | ||||
8 | 5th group, Tamper ZW3, sent as secure |
Технология | Z-Wave+ |
---|---|
Z-Wave Plus: | Нет |
Производитель | Fibaro |
Тип датчика | геркон |
Внутренняя/наружная установка | Внутренняя |
Источник питания | Батарея |
Тип батареи | 1/2 AA (ER14250) |
Форм-фактор | Настенный |
Назначение | Закрытие и отслеживание состояния двери |
OTA обновление прошивки | Да |