Z-Wave Plus Fibaro Вставное реле 1 * 2.5 кВт

Есть в наличии
SKU
FIB_FGS-213
Начиная с 5 390,00 руб.
  • Compatible with any Z-Wave or Z-Wave+ Controller
  • Supports protected mode (Z-Wave network security mode) with AES-128 encryption
  • Advanced microprocessor control
  • Active power and energy metering functionality
  • Works with various types of switches – momentary, toggle, three-way, etc
  • To be installed in wall switch boxes of dimensions allowing for installation, conforming to provisions of applicable regulations
  • FIBARO Switch 2 is an extension unit.

THE NEW GENERATION OF RELAY SWITCHES

Вставное реле предназначено для установки в монтажную коробку позади традиционного выключателя. Устройством можно управлять как локально, так и дистанционно. Выключатель имеет внутреннее реле для управления подключенной нагрузкой. С данным реле, существующие выключатели могут превратиться в умную систему Z-Wave, оставляя традиционные выключатели на месте. Это необходимо когда пользователь не хочет менять имеющиеся выключатели, а желает управлять и контролировать их дистанционно с помощью Z-Wave технологии.

FIBARO Switch 2 is designed to be installed in standard wall switch boxes or anywhere else where it is necessary to control electric devices. FIBARO Switch 2 allows to control connected devices either via the Z-Wave+ network or via a switch connected directly to it and is equipped with active power and energy consumption metering functionality.

Note: This module requires the Neutral to operate. The output is not potential-free, it does not allow to control a dry contact or load another supply voltage than the input.

  • Requires 3-wire (including neutral) installation
  • Can use mains or alternative power supply for load (including DC)
  • Works with AC power supply only (110-230V AC)
  • Supports secure mode (Z-Wave Network Security) encrypted with AES-128
  • Energy and power measurement of connected devices
  • Built-in scene activation mechanism
  • Security and notification communication classes
  • Configuration menu with a diode
  • Latest generation Z-Wave 500 series chip
  • Z-Wave Plus protocol
  • Energy and power measurement of connected devices
  • Supports secure mode (Z-Wave Network Security) encrypted with AES-128
  • A complex system of control for each channel
  • A complex system of scene activation for each channel (scene management)
  • 1 to 3 presses and holding the key pressed down can be mapped to four different actions
  • Very accurate energy measurement +/- 1 % for power above 5W
  • Smart notifications
  • Sockets with more convenient connectors
  • User-friendly configuration menu
  • Z-Wave network coverage tester
  • Software updates*
Радиус действия

Чем больше диапазон действия, тем более надежным является продукт - устройство имеет первоклассную антенну. Оптимизированное для надежности, это устройство может взаимодействовать беспроводным способом на расстояния более 150 метров.

Поколение 5

Лучше антенна. Лучше Z-Wave. Устройство разработано на технологии Z-Wave Plus последнего 5го поколения, чтобы предоставить вам самое быстрое время отклика и оптимальное время жизни батареи между перезарядками.

Безопасность

Если вы используете устройство для обеспечения безопасности, вы хотите чтобы взаимодействие было защищенным. Вот почему устройство использует беспроводное шифрование AES-128 для защиты от несанкционированного доступа и хакеров.

Беспроводное обновление

Используете ли вы устройство для комфорта или безопасности, вы желаете чтобы оно всегда оставалось обновленным до последней версии. Как бы не создавались обновления прошивки для устройства, вы всегда можете обновить его с помощью Microsoft Windows или выбрать Z-Wave контроллер.

Technical Specification

  • HARDWARE
    • Z-Wave Chip 500 series
  • COMMUNICATION PROTOCOLS
    • Z-Wave Plus
  • LED AND BUTTONS
    • LED indicator
    • Include/Exclude button
  • MAXIMUM LOAD
    • 8A (Resistive)
  • OVERCURRENT PROTECTION
    • required external 10A circuit breaker
  • DIMENSIONS
    • 42.5 x 38.25 x 20.3mm (LxWxH)
  • CERTIFICATIONS
    • FCC, DEKRA, Z-Wave
  • POWER SUPPLY
    • Input: AC 100-240VAC, 50-60Hz
  • POWER CONSUMPTION
    • up to 0.8W
  • RADIO SIGNAL POWER
    • up to 1mW
  • RANGE
    •  up to 50m (outdoors) and 40m (indoors)
  • OPERATIONAL TEMPERATURE
    • 0-35°C
  • FOR INSTALLATION IN BOXES
    • D ≥ 50mm, depth ≥ 60mm

Package content

  • Unit
  • User manual

Additional Info

Z-Wave Association Capabilities

Model: FIBARO Single Switch 2 (FGS-213)

Z-Wave Certification Number: ZC10-16075135


Group ID

Maximum Nodes

Description

1 1 “Lifeline” reports the device status and allows for assigning single device only (main controller by default).
2 5 “On/Off (S1)” is assigned to switch connected to the S1 terminal (uses Basic command class).
3 5 “Dimmer (S1)” is assigned to switch connected to the S1 terminal (uses Switch Multilevel command class).
4 5 “On/Off (S2)” is assigned to switch connected to the S2 terminal (uses Basic command class).
5 5 “Dimmer (S2)” is assigned to switch connected to the S2 terminal (uses Switch Multilevel command class).

Z-Wave Configuration Capabilities

Model: FIBARO Single Switch 2 (FGS-213)

Z-Wave Certification Number: ZC10-16075135


Parameter Number

Parameter Size

Parameter Name

Parameter Values

10 1 First channel - operating mode 0
(Default)
standard operation
  1 delay ON function
  2 delay OFF function
  3 auto ON function
  4 auto OFF function
  5 flash function

Parameter Number

Parameter Size

Parameter Name

Parameter Values

11 1 First channel - reaction to switch for delay/auto ON/OFF modes 0
(Default)
cancel mode and set target state
  1 no reaction to switch - mode runs until it ends
  2 reset timer - start counting from the beginning

Parameter Number

Parameter Size

Parameter Name

Parameter Values

12 2 First channel - time parameter for delay/auto ON/OFF modes 0 0.1s
  1 to 32000
(Default)
1-32000s, 1s step

Parameter Number

Parameter Size

Parameter Name

Parameter Values

13 2 First channel - pulse time for flashing mode 1 to 32000
(Default)
(0.1-3200.0s, 0.1s step) - time parameter

Parameter Number

Parameter Size

Parameter Name

Parameter Values

20 1 Switch type 0 momentary switch
  1 toggle switch (contact closed - ON, contact opened - OFF)
  2
(Default)
toggle switch (device changes status when switch changes status)

Parameter Number

Parameter Size

Parameter Name

Parameter Values

21 1 Flashing mode - reports 0
(Default)
the device does not send reports
  1 the device sends reports

Parameter Number

Parameter Size

Parameter Name

Parameter Values

27 1 Associations in Z-Wave network security mode 1 2nd group sent as secure
  2 3rd group sent as secure
  4 4th group sent as secure
  8 5th group sent as secure

Parameter Number

Parameter Size

Parameter Name

Parameter Values

28 1 S1 switch - scenes sent 1 Key pressed 1 time
  2 Key pressed 2 time
  4 Key pressed 3 time
  8 Key Hold Down and Key Released

Parameter Number

Parameter Size

Parameter Name

Parameter Values

29 1 S2 switch - scenes sent 1 Key pressed 1 time
  2 Key pressed 2 times
  4 Key pressed 3 times
  8 Key Hold Down and Key Released

Parameter Number

Parameter Size

Parameter Name

Parameter Values

30 1 S1 switch - associations sent to 2nd and 3rd association groups 1 ignore turning ON with 1 click of the switch
  2 ignore turning OFF with 1 click of the switch
  4 ignore holding and releasing the switch*
  8 ignore double click of the switch**

Parameter Number

Parameter Size

Parameter Name

Parameter Values

31 2 S1 switch - Switch ON value sent to 2nd and 3rd association groups 0 to 255
(Default)
sent value

Parameter Number

Parameter Size

Parameter Name

Parameter Values

32 2 S1 switch - Switch OFF value sent to 2nd and 3rd association groups 0 to 255
(Default)
sent value

Parameter Number

Parameter Size

Parameter Name

Parameter Values

33 2 S1 switch - Double Click value sent to 2nd and 3rd association groups 0 to 255
(Default)
sent value

Parameter Number

Parameter Size

Parameter Name

Parameter Values

35 1 S2 switch - associations sent to 4th and 5th association groups 1 ignore turning on with 1 click of the switch
  2 ignore turning off with 1 click of the switch
  4 ignore holding and releasing the switch*
  8 ignore double click of the switch**

Parameter Number

Parameter Size

Parameter Name

Parameter Values

36 2 S2 switch - Switch ON value sent to 4th and 5th association groups 0 to 255
(Default)
sent value

Parameter Number

Parameter Size

Parameter Name

Parameter Values

37 2 S2 switch - Switch OFF value sent to 4th and 5th association groups 0 to 255
(Default)
sent value

Parameter Number

Parameter Size

Parameter Name

Parameter Values

38 2 S2 switch - Double Click value sent to 4th and 5th association groups 0 to 255
(Default)
sent value

Parameter Number

Parameter Size

Parameter Name

Parameter Values

40 1 Reaction to General Alarm 0 alarm frame is ignored
  1 turn ON after receiving the alarm frame
  2 turn OFF after receiving the alarm frame
  3
(Default)
flash after receiving the alarm frame

Parameter Number

Parameter Size

Parameter Name

Parameter Values

41 1 Reaction to Flood Alarm 0 alarm frame is ignored
  1 turn ON after receiving the alarm frame
  2
(Default)
turn OFF after receiving the alarm frame
  3 flash after receiving the alarm frame

Parameter Number

Parameter Size

Parameter Name

Parameter Values

42 1 Reaction to CO/CO2/Smoke Alarm 0 alarm frame is ignored
  1 turn ON after receiving the alarm frame
  2 turn OFF after receiving the alarm frame
  3
(Default)
flash after receiving the alarm frame

Parameter Number

Parameter Size

Parameter Name

Parameter Values

43 1 Reaction to Heat Alarm 0 alarm frame is ignored
  1
(Default)
turn ON after receiving the alarm frame
  2 turn OFF after receiving the alarm frame
  3 flash after receiving the alarm frame

Parameter Number

Parameter Size

Parameter Name

Parameter Values

44 2 Flashing alarm duration 1 to 32000
(Default)
1-32000s, 1s step - duration

Parameter Number

Parameter Size

Parameter Name

Parameter Values

50 1 First channel - power reports 0 reports are disabled
  1 to 100
(Default)
change in power

Parameter Number

Parameter Size

Parameter Name

Parameter Values

51 1 First channel - minimal time between power reports 0 reports are disabled
  1 to 120
(Default)
1-120s - report interval

Parameter Number

Parameter Size

Parameter Name

Parameter Values

53 2 First channel - energy reports 0 reports are disabled
  1 to 32000
(Default)
1-32000 (1-32000Wh) - change in energy

Parameter Number

Parameter Size

Parameter Name

Parameter Values

58 2 Periodic power reports 0 periodic reports are disabled
  1 to 32000
(Default)
1-32000s - report interval

Parameter Number

Parameter Size

Parameter Name

Parameter Values

59 2 Periodic energy reports 0 periodic reports are disabled
  1 to 32000
(Default)
1-32000s - report interval

Parameter Number

Parameter Size

Parameter Name

Parameter Values

60 1 Measuring energy consumed by the device itself 0
(Default)
function inactive
  1 function active

Parameter Number

Parameter Size

Parameter Name

Parameter Values

9 1 Restore state after power failure 0 the device does not save the state prior to the power failure and returns to „off” position
  1
(Default)
the device restores its state prior to the power failure

Z-Wave Command Classes

Model: FIBARO Single Switch 2 (FGS-213)

Z-Wave Certification Number: ZC10-16075135


Supported Command Classes
 
        All Switch
        Application Status
        Association Group Information
        Association V2
        Basic
        Central Scene V2
        Configuration
        CRC16 Encapsulation
        Device Reset Local
        Firmware Update MD V3
        Manufacturer Specific V2
        Meter V3
        Multi-Channel_V4
        Multi-Channel-Association_V3
        Notification V5
        Powerlevel
        Protection V2
        Security
        Switch Binary
        Version V2
        Z-Wave Plus Info V2
 
 
Controlled Command Classes
 
        Basic
        Notification V5
        Switch Multilevel V3

User manual

Guides

  • Guides
Дополнительная информация
Z-Wave Plus: Нет
Z-Wave аппаратная платформа ZM5101
Z-Wave тип библиотеки Enhanced 232 Slave
Z-Wave тип устройства On/Off Power Switch
Z-Wave тип роли Always On Slave
Технология Z-Wave+
Внутренняя/наружная установка Внутренняя
Производитель Fibaro
Группы ассоциаций 5
Z-Wave Функции Запуск сцен, Multichanel , Multichannel Association
Поддерживаемые типы выключателей/управления Кнопочный, Тумблерный, Кулисный, Без подсветки
Максимальная нагрузка 7.5A
Тип диммера и выключателя insert module
Источник питания Кабель AC
Тип проводной системы 3-Wire
Тип вставного модуля Relay - Single
Функции вставных модулей Измерение мощности
Способы нажатия Одно нажатие
Форм-фактор Монтаж в стену
Назначение Управление освещением
OTA обновление прошивки Да
Напишите ваш собственный отзыв
Only registered users can write reviews. Please Sign in or create an account
Copyright © 2009-2020 Swinestudio. All rights reserved.