Z-Wave Plus Philio Контроллер рольставен

Есть в наличии
SKU
PHI_PAN08
Начиная с 3 190,00 руб.

Controller for all blinds, awnings, garage doors and gates

  • Wireless control of any AC Motor
  • Precise positioning of blind or awning
  • Automatic calibration
  • Monitor and analyse energy usage

The in-wall Roller Shutter Controller is designed to switch rise/lower roller shutter connected to its terminals using radio waves, controllers and a push button directly connected to this Roller Controller. 
This in-wall Roller Shutter Controller is a transceiver which is a Z-Wave Plus™
enabled device and is fully compatible with any Z-Wave™ enabled network. Slim design let the Controller can easily hide itself into the wall box and that will be good for the house decoration. 
The new smart relay calibration technology can reduce the inrush current caused by the load and let the module work perfectly with many kind of Roller Shutter. 
This in-wall Roller Shutter Controller is able to detect position of the Shutter by using the patterned power measuring method, so it can be remote controlled not only fully up or down, but also can be adjusted to ex. 30% or 50%. And when manual controlled by push button, the controller also can memorize the position and send the new shutter position to its controller (ex. IP-Gateway).


Wireless range

The better the wireless range, the more reliable the product, and device offers a class-leading antenna. Optimised for reliability, this tiny unit  can wireless communicate over 150 metres.

Gen5

The best antenna. The best Z-Wave. Device is built upon Z-Wave Plus and leading Gen5 technology to offer you the fastest response times and optimal battery life between recharges.

Secure security

If you’re using a sensor for security you want its communication to be secure. That’s why unit utilises AES-128 wireless data encryption to keep it secure from prying eyes and hackers.

Wireless updates.

Whether used for home intelligence or security, you want your device to always stay up to date. Whenever firmware udpdates are made for it, you’ll be able to upgrade unit via Microsoft Windows or select Z-Wave gateways.


Technical Specification

  • MODEL NUMBER
    • PAN08
  • HARDWARE
    • Z-Wave Chip 500 series
  • COMMUNICATION PROTOCOLS
    • Z-Wave Plus
  • FEATURES
    • Auto calibration
    • Auto feedback the roller shutter position
    • Type of supported motor: single-phase AC motors
    • Supported limit switches type: electronic and mechanic
    • Connected motor’s current and historical power consumption measured
  • LED AND BUTTONS
    • LED indicator
    • Include/Exclude button
  • ASSOCIATION GROUP
    • One group and one device (nodes)
  • MAXIMUM CURRENT
    • 5A for lamps and resistive loads
    • 1.7A for motors with compensated power factor (inductive loads)
  • MAXIMUM LOAD
    • 1100W (Resistive loads)
    • 400W (Inductive loads)
  • OVERLOAD PROTECTION
    • Overload protection
  • DIMENSIONS
    • 47.5 x 39 x 15.6 mm (LxWxH)
  • CERTIFICATIONS
    • FCC, DEKRA, Z-Wave
  • POWER SUPPLY
    • Input: AC 100-240VAC, 50-60Hz
  • POWER CONSUMPTION
    • up to 0.8W
  • RADIO SIGNAL POWER
    • up to 1mW
  • RANGE
    •  up to 50m (outdoors) and 40m (indoors)
  • OPERATIONAL TEMPERATURE
    • 0-40°C
  • FOR INSTALLATION IN BOXES
    • D ≥ 50mm, depth ≥ 60mm

Package content

  • Unit
  • User manual

Z-Wave Specification

Z-Wave Association Capabilities

Model: Roller shutter controller (PAN08-1A)

Z-Wave Certification Number: ZC10-14110006


Group ID

Maximum Nodes

Description

1 1 Z-Wave Plus Lifeline

Z-Wave Configuration Capabilities

Model: Roller shutter controller (PAN08-1A)

Z-Wave Certification Number: ZC10-14110006


Parameter Number

Parameter Size

Parameter Name

Parameter Values

1 2 Watt Meter Report Period 1 to 32767
(Default)
5*720s=3600s=1 hour

Parameter Number

Parameter Size

Parameter Name

Parameter Values

2 2 KWH Meter Report Period 1 to 32767
(Default)
6*10min= 1 hour

Parameter Number

Parameter Size

Parameter Name

Parameter Values

3 2 Threshold of current for load caution 10 to 500
(Default)
500*0.01A=5A

Parameter Number

Parameter Size

Parameter Name

Parameter Values

4 2 Threshold of KWh for Load Caution 1 to 10000
(Default)

Parameter Number

Parameter Size

Parameter Name

Parameter Values

5 1 External switch type 1 One Push Button: When the configuration setting is One Push Button, only S1 input will be valid. The control moving commands can be accepted in this switch type while the shutter is moving. In this switch type, the inclusion/exclusion/reset/association function can also be fulfilled by pressing S1 just like the operation of include button. When S1 is short pressed, the shutter will move up toward TOP(0xFF). While in this moving S1 is short pressed again, the shutter will stop moving. A third short pressing of S1 will move the shutter down toward BOTTOM(0x00). While in this moving S1 is short pressed again, the shutter will stop moving. And so on… Inverting direction and stopping.
  2
(Default)
Two Push Button: (The default setting is Two Push Button (2)) If this setting is configured as Two Push Button, S1 and S2 input will be valid, but will not accept pressing S1and S2 at the same time. In this switch type, the inclusion/exclusion/reset/association function can also be fulfilled by pressing S1 or S2 just like the operation of include button. When S1 is pressed and hold more than 1.5 seconds, the shutter will move up toward TOP(0xFF), and the shutter will stop moving when S1 is released. When S2 is pressed and hold more than 1.5 seconds, the shutter will move down toward BOTTOM(0x00), and the shutter will stop moving when S2 is released. When S1 is short pressed, the shutter will move up toward TOP(0xFF). While in this moving short pressed S1 again, the shutter just keep moving up toward TOP(0xFF). The easy way to stop this moving is short pressing S2. When S2 is short pressed, the shutter will move down toward BOTTON(0x00). While in this moving short pressed S2 again, the shutter just keep moving down toward BOTTON(0x00). The easy way to stop this moving is short pressing S1.

Parameter Number

Parameter Size

Parameter Name

Parameter Values

6 1 Level Report mode 1 Mode 1 : In 5 seconds period after controlled by a moving command, it will report the destination level when received request command. Out of the 5 seconds period, it will report the actual level of the shutter when received request command.
  2
(Default)
Mode 2 : Whenever the shutter move pass a 10 percent level, it will auto report the level to Group 1 node.

Z-Wave Command Classes

Model: Roller shutter controller (PAN08-1A)

Z-Wave Certification Number: ZC10-14110006


Supported Command Classes
 
        Alarm
        Association
        Association Group Information
        Basic
        Configuration
        Device Reset Local
        Firmware Update Meta Data
        Manufacturer Specific
        Meter
        Powerlevel
        Scene Activation
        Scene Actuator Configuration
        Switch Binary
        Switch Multilevel
        Version
        ZWavePlus Info

User manual

Guides

  • Guides
Дополнительная информация
Технология Z-Wave+
Z-Wave Plus: Нет
Z-Wave аппаратная платформа ZM5202
Z-Wave тип библиотеки Enhanced 232 Slave
Z-Wave тип устройства Window Covering - Pos/End Aware
Z-Wave тип роли Always On Slave
Внутренняя/наружная установка Внутренняя
Производитель Philio
Группы ассоциаций 1
Z-Wave Функции Run Scene
Источник питания Кабель AC
Максимальная нагрузка 1.5A
Форм-фактор Настенный
Назначение оконные жалюзи
OTA обновление прошивки Да
Напишите ваш собственный отзыв
Only registered users can write reviews. Please Sign in or create an account
Copyright © 2009-2017 Swinestudio. All rights reserved.