Z-Wave Plus TKB Home Контроллер рольставен
Controller for all blinds, awnings, garage doors and gates
- Wireless control of any AC Motor
- Precise positioning of blind or awning
- Automatic calibration
- Monitor and analyse energy usage
The in-wall Roller Shutter Controller is designed to switch rise/lower roller shutter connected to its terminals using radio waves, controllers and a push button directly connected to this Roller Controller.
This in-wall Roller Shutter Controller is a transceiver which is a Z-Wave Plus™
enabled device and is fully compatible with any Z-Wave™ enabled network. Slim design let the Controller can easily hide itself into the wall box and that will be good for the house decoration.
The new smart relay calibration technology can reduce the inrush current caused by the load and let the module work perfectly with many kind of Roller Shutter.
This in-wall Roller Shutter Controller is able to detect position of the Shutter by using the patterned power measuring method, so it can be remote controlled not only fully up or down, but also can be adjusted to ex. 30% or 50%. And when manual controlled by push button, the controller also can memorize the position and send the new shutter position to its controller (ex. IP-Gateway).
Чем больше диапазон действия, тем более надежным является продукт - устройство имеет первоклассную антенну. Оптимизированное для надежности, это устройство может взаимодействовать беспроводным способом на расстояния более 150 метров.
Лучше антенна. Лучше Z-Wave. Устройство разработано на технологии Z-Wave Plus последнего 5го поколения, чтобы предоставить вам самое быстрое время отклика и оптимальное время жизни батареи между перезарядками.
Если вы используете устройство для обеспечения безопасности, вы хотите чтобы взаимодействие было защищенным. Вот почему устройство использует беспроводное шифрование AES-128 для защиты от несанкционированного доступа и хакеров.
Используете ли вы устройство для комфорта или безопасности, вы желаете чтобы оно всегда оставалось обновленным до последней версии. Как бы не создавались обновления прошивки для устройства, вы всегда можете обновить его с помощью Microsoft Windows или выбрать Z-Wave контроллер.
Technical Specification
- MODEL NUMBER
- TZ75
- HARDWARE
- Z-Wave Chip 500 series
- COMMUNICATION PROTOCOLS
- Z-Wave Plus
- FEATURES
- Auto calibration
- Auto feedback the roller shutter position
- Type of supported motor: single-phase AC motors
- Supported limit switches type: electronic and mechanic
- Connected motor’s current and historical power consumption measured
- LED AND BUTTONS
- LED indicator
- Include/Exclude button
- ASSOCIATION GROUP
- One group and one device (nodes)
- MAXIMUM CURRENT
- 5A for lamps and resistive loads
- 1.7A for motors with compensated power factor (inductive loads)
- MAXIMUM LOAD
- 1100W (Resistive loads)
- 400W (Inductive loads)
- OVERLOAD PROTECTION
- Overload protection
- DIMENSIONS
- 47.5 x 39 x 15.6 mm (LxWxH)
- CERTIFICATIONS
- FCC, DEKRA, Z-Wave
- POWER SUPPLY
- Input: AC 100-240VAC, 50-60Hz
- POWER CONSUMPTION
- up to 0.8W
- RADIO SIGNAL POWER
- up to 1mW
- RANGE
- up to 50m (outdoors) and 40m (indoors)
- OPERATIONAL TEMPERATURE
- 0-40°C
- FOR INSTALLATION IN BOXES
- D ≥ 50mm, depth ≥ 60mm
Package content
- Unit
- User manual
Z-Wave Specification
- Z-Wave Alliance
- Manufacturer
Z-Wave Association Capabilities
Model: Roller shutter controller (PAN08-1A)
Z-Wave Certification Number: ZC10-14110006
Group ID |
Maximum Nodes |
Description |
1 | 1 | Z-Wave Plus Lifeline |
Z-Wave Configuration Capabilities
Model: Roller shutter controller (PAN08-1A)
Z-Wave Certification Number: ZC10-14110006
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
1 | 2 | Watt Meter Report Period | 1 to 32767 (Default) |
5*720s=3600s=1 hour | |
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
2 | 2 | KWH Meter Report Period | 1 to 32767 (Default) |
6*10min= 1 hour | |
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
3 | 2 | Threshold of current for load caution | 10 to 500 (Default) |
500*0.01A=5A | |
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
4 | 2 | Threshold of KWh for Load Caution | 1 to 10000 (Default) |
||
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
5 | 1 | External switch type | 1 | One Push Button: When the configuration setting is One Push Button, only S1 input will be valid. The control moving commands can be accepted in this switch type while the shutter is moving. In this switch type, the inclusion/exclusion/reset/association function can also be fulfilled by pressing S1 just like the operation of include button. When S1 is short pressed, the shutter will move up toward TOP(0xFF). While in this moving S1 is short pressed again, the shutter will stop moving. A third short pressing of S1 will move the shutter down toward BOTTOM(0x00). While in this moving S1 is short pressed again, the shutter will stop moving. And so on… Inverting direction and stopping. | |
2 (Default) |
Two Push Button: (The default setting is Two Push Button (2)) If this setting is configured as Two Push Button, S1 and S2 input will be valid, but will not accept pressing S1and S2 at the same time. In this switch type, the inclusion/exclusion/reset/association function can also be fulfilled by pressing S1 or S2 just like the operation of include button. When S1 is pressed and hold more than 1.5 seconds, the shutter will move up toward TOP(0xFF), and the shutter will stop moving when S1 is released. When S2 is pressed and hold more than 1.5 seconds, the shutter will move down toward BOTTOM(0x00), and the shutter will stop moving when S2 is released. When S1 is short pressed, the shutter will move up toward TOP(0xFF). While in this moving short pressed S1 again, the shutter just keep moving up toward TOP(0xFF). The easy way to stop this moving is short pressing S2. When S2 is short pressed, the shutter will move down toward BOTTON(0x00). While in this moving short pressed S2 again, the shutter just keep moving down toward BOTTON(0x00). The easy way to stop this moving is short pressing S1. | ||||
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
6 | 1 | Level Report mode | 1 | Mode 1 : In 5 seconds period after controlled by a moving command, it will report the destination level when received request command. Out of the 5 seconds period, it will report the actual level of the shutter when received request command. | |
2 (Default) |
Mode 2 : Whenever the shutter move pass a 10 percent level, it will auto report the level to Group 1 node. |
Z-Wave Command Classes
Model: Roller shutter controller (PAN08-1A)
Z-Wave Certification Number: ZC10-14110006
Supported Command Classes |
Alarm |
Association |
Association Group Information |
Basic |
Configuration |
Device Reset Local |
Firmware Update Meta Data |
Manufacturer Specific |
Meter |
Powerlevel |
Scene Activation |
Scene Actuator Configuration |
Switch Binary |
Switch Multilevel |
Version |
ZWavePlus Info |
User manual
- Manual (RUS)
- Manual (ENG)
- Manufacturer manual
Guides
- Guides (RUS)
- Guides (ENG)
- Manufacturer guides
Технология | Z-Wave+ |
---|---|
Z-Wave Plus: | Да |
Z-Wave аппаратная платформа | ZM5202 |
Z-Wave тип библиотеки | Enhanced 232 Slave |
Z-Wave тип устройства | Window Covering - Pos/End Aware |
Z-Wave тип роли | Always On Slave |
Внутренняя/наружная установка | Внутренняя |
Производитель | TKB Home |
Группы ассоциаций | 1 |
Z-Wave Функции | Multilevel |
Функции жалюзи | Калибровка |
Поддерживаемые типы выключателей/управления | Кнопочный, Тумблерный, Кулисный, Без подсветки |
Источник питания | Кабель AC |
Максимальная нагрузка | 5A |
Форм-фактор | Настенный |
Назначение | оконные жалюзи |
OTA обновление прошивки | Да |