Z-Wave Plus Fibaro Вставное реле 2 * 1.5 kW
- Совместим с любыми Z-Wave или Z-Wave + контроллерами
- Поддерживает защищенный режим (режим защиты Z-Wave сети) с шифрованием AES-128
- Расширенное управление микропроцессором
- Измерение мгновенной мощности и энергопотребления
- Работает с различными типами выключателей - кнопочный, тумблерный, кулисный, трехпозиционный и др.
- Предназначен для установки в монтажные коробки
- FIBARO Выключатель 2 - это вставной модуль
THE NEW GENERATION OF RELAY SWITCHES
Вставное реле предназначено для установки в монтажную коробку позади традиционного выключателя. Устройством можно управлять как локально, так и дистанционно. Выключатель имеет внутреннее реле для управления подключенной нагрузкой. С данным реле, существующие выключатели могут превратиться в умную систему Z-Wave, оставляя традиционные выключатели на месте. Это необходимо когда пользователь не хочет менять имеющиеся выключатели, а желает управлять и контролировать их дистанционно с помощью Z-Wave технологии.
FIBARO Switch 2 is designed to be installed in standard wall switch boxes or anywhere else where it is necessary to control electric devices. FIBARO Switch 2 allows to control connected devices either via the Z-Wave+ network or via a switch connected directly to it and is equipped with active power and energy consumption metering functionality.
Note: This module requires the Neutral to operate. The output is not potential-free, it does not allow to control a dry contact or load another supply voltage than the input.
- Requires 3-wire (including neutral) installation
- Can use mains or alternative power supply for load (including DC)
- Works with AC power supply only (110-230V AC)
- Supports secure mode (Z-Wave Network Security) encrypted with AES-128
- Energy and power measurement of connected devices
- Built-in scene activation mechanism
- Security and notification communication classes
- Configuration menu with a diode
- Latest generation Z-Wave 500 series chip
- Z-Wave Plus protocol
- Energy and power measurement of connected devices
- Supports secure mode (Z-Wave Network Security) encrypted with AES-128
- A complex system of control for each channel
- A complex system of scene activation for each channel (scene management)
- 1 to 3 presses and holding the key pressed down can be mapped to four different actions
- Very accurate energy measurement +/- 1 % for power above 5W
- Smart notifications
- Sockets with more convenient connectors
- User-friendly configuration menu
- Z-Wave network coverage tester
- Software updates*
Technical Specification
- HARDWARE
- Z-Wave Chip 500 series
- COMMUNICATION PROTOCOLS
- Z-Wave Plus
- LED AND BUTTONS
- LED indicator
- Include/Exclude button
- MAXIMUM LOAD
- 6.5A per channel, 10A overall (Resistive)
- OVERCURRENT PROTECTION
- required external 10A circuit breaker
- DIMENSIONS
- 42.5 x 38.25 x 20.3mm (LxWxH)
- CERTIFICATIONS
- FCC, DEKRA, Z-Wave
- POWER SUPPLY
- Input: AC 100-240VAC, 50-60Hz
- POWER CONSUMPTION
- up to 0.8W
- RADIO SIGNAL POWER
- up to 1mW
- RANGE
- up to 50m (outdoors) and 40m (indoors)
- OPERATIONAL TEMPERATURE
- 0-35°C
- FOR INSTALLATION IN BOXES
- D ≥ 50mm, depth ≥ 60mm
Package content
- Unit
- User manual
Additional Info
Z-Wave Association Capabilities
Model: FIBARO Double Switch 2 (FGS-223)
Z-Wave Certification Number: ZC10-16075136
Group ID |
Maximum Nodes |
Description |
1 | 1 | “Lifeline” reports the device status and allows for assigning single device only (main controller by default). |
2 | 5 | “On/Off (S1)” is assigned to switch connected to the S1 terminal (uses Basic command class). |
3 | 5 | “Dimmer (S1)” is assigned to switch connected to the S1 terminal (uses Switch Multilevel command class). |
4 | 5 | “On/Off (S2)” is assigned to switch connected to the S2 terminal (uses Basic command class). |
5 | 5 | “Dimmer (S2)” is assigned to switch connected to the S2 terminal (uses Switch Multilevel command class). |
Z-Wave Configuration Capabilities
Model: FIBARO Double Switch 2 (FGS-223)
Z-Wave Certification Number: ZC10-16075136
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
10 | 1 | First channel - operating mode | 0 (Default) |
standard operation | |
1 | delay ON function | ||||
2 | delay OFF function | ||||
3 | auto ON function | ||||
4 | auto OFF function | ||||
5 | flash function | ||||
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
11 | 1 | First channel - reaction to switch for delay/auto ON/OFF modes | 0 (Default) |
cancel mode and set target state | |
1 | no reaction to switch - mode runs until it ends | ||||
2 | reset timer - start counting from the beginning | ||||
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
12 | 2 | First channel - time parameter for delay/auto ON/OFF modes | 0 | 0.1s | |
1 to 32000 (Default) |
1-32000s, 1s step | ||||
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
13 | 2 | First channel - pulse time for flashing mode | 1 to 32000 (Default) |
0.1-3200.0s, 0.1s step | |
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
15 | 1 | Second channel - operating mode | 0 (Default) |
standard operation | |
1 | delay ON function | ||||
2 | delay OFF function | ||||
3 | auto ON function | ||||
4 | auto OFF function | ||||
5 | flash function | ||||
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
16 | 1 | Second channel - reaction to switch for delay/auto ON/OFF modes | 0 (Default) |
cancel mode and set target state | |
1 | no reaction to switch - mode runs until it ends | ||||
2 | reset timer - start counting from the beginning | ||||
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
17 | 2 | Second channel - time parameter for delay/auto ON/OFF modes | 0 | 0.1s | |
1 to 32000 (Default) |
1-32000s, 1s step | ||||
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
18 | 2 | Second channel - pulse time for flashing mode | 1 to 32000 (Default) |
0.1-3200.0s, 0.1s step | |
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
20 | 1 | Switch type | 0 | momentary switch | |
1 | toggle switch (contact closed - ON, contact opened - OFF) | ||||
2 (Default) |
toggle switch (device changes status when switch changes status) | ||||
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
21 | 1 | Flashing mode - reports | 0 (Default) |
the device does not send reports | |
1 | the device sends reports | ||||
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
27 | 1 | Associations in Z-Wave network security mode | 1 | 2nd group sent as secure | |
2 | 3rd group sent as secure | ||||
4 | 4th group sent as secure | ||||
8 | 5th group sent as secure | ||||
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
28 | 1 | S1 switch - scenes sent | 1 | Key pressed 1 time | |
2 | Key pressed 2 time | ||||
4 | Key pressed 3 time | ||||
8 | Key Hold Down and Key Released | ||||
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
29 | 1 | S2 switch - scenes sent | 1 | Key pressed 1 time | |
2 | Key pressed 2 time | ||||
4 | Key pressed 3 time | ||||
8 | Key Hold Down and Key Released | ||||
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
30 | 1 | S1 switch - associations sent to 2nd and 3rd association groups | 1 | ignore turning ON with 1 click of the switch | |
2 | ignore turning OFF with 1 click of the switch | ||||
4 | ignore holding and releasing the switch* | ||||
8 | ignore double click of the switch** | ||||
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
31 | 2 | S1 switch - Switch ON value sent to 2nd and 3rd association groups | 0 to 255 (Default) |
||
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
32 | 2 | S1 switch - Switch OFF value sent to 2nd and 3rd association groups | 0 (Default) |
turning off associated devices | |
1 to 99 | forcing level of associated devices | ||||
255 | setting associated devices to the last remembered state or turning them on | ||||
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
33 | 2 | S1 switch - Double Click value sent to 2nd and 3rd association groups | 0 to 255 (Default) |
||
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
35 | 1 | S2 switch - associations sent to 2nd and 3rd association groups | 1 | NOTE Parameter 35 values may be combined, e.g. 1+2=3 means that associations for turning ON and OFF are not sent. | |
2 | ignore turning off with 1 click of the switch | ||||
4 | ignore holding and releasing the switch* | ||||
8 | ignore double click of the switch** | ||||
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
36 | 2 | S2 switch - Switch ON value sent to 2nd and 3rd association groups | 0 | turning off associated devices | |
1 to 99 | forcing level of associated devices | ||||
255 (Default) |
setting associated devices to the last remembered state or turning them on | ||||
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
37 | 2 | S2 switch - Switch OFF value sent to 2nd and 3rd association groups | 0 (Default) |
turning off associated devices | |
1 to 99 | forcing level of associated devices | ||||
255 | setting associated devices to the last remembered state or turning them on | ||||
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
38 | 2 | S2 switch - Double Click value sent to 2nd and 3rd association groups | 0 | turning off associated devices | |
1 to 99 (Default) |
forcing level of associated devices | ||||
255 | setting associated devices to the last remembered state or turning them on | ||||
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
40 | 1 | Reaction to General Alarm | 0 | alarm frame is ignored | |
1 | turn ON after receiving the alarm frame | ||||
2 | turn OFF after receiving the alarm frame | ||||
3 (Default) |
flash after receiving the alarm frame | ||||
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
41 | 1 | Reaction to Flood Alarm | 0 | alarm frame is ignored | |
1 | alarm frame is ignored | ||||
2 (Default) |
turn OFF after receiving the alarm frame | ||||
3 | flash after receiving the alarm frame | ||||
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
42 | 1 | Reaction to CO/CO2/Smoke Alarm | 0 | alarm frame is ignored | |
1 | turn ON after receiving the alarm frame | ||||
2 | turn OFF after receiving the alarm frame | ||||
3 (Default) |
flash after receiving the alarm frame | ||||
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
43 | 1 | Reaction to Heat Alarm | 0 | alarm frame is ignored | |
1 (Default) |
turn ON after receiving the alarm frame | ||||
2 | turn OFF after receiving the alarm frame | ||||
3 | flash after receiving the alarm frame | ||||
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
44 | 2 | Flashing alarm duration | 1 to 32000 (Default) |
1-32000s, 1s step | |
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
50 | 1 | First channel - power reports | 0 | reports are disabled | |
1 to 100 (Default) |
(1-100%) - change in power | ||||
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
51 | 1 | First channel - minimal time between power reports | 0 | periodic reports are disabled | |
1 to 120 (Default) |
(1-120s) - report interval | ||||
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
53 | 2 | First channel - energy reports | 0 | reports are disabled | |
1 to 32000 (Default) |
1-32000 (1-32000Wh) - change in energy | ||||
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
54 | 1 | Second channel - power reports | 0 | reports are disabled | |
1 to 100 (Default) |
(1-100%) - change in power | ||||
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
55 | 1 | Second channel - minimal time between power reports | 0 | periodic reports are disabled | |
1 to 120 (Default) |
(1-120s) - report interval | ||||
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
57 | 2 | Second channel - energy reports | 0 | reports are disabled | |
1 to 32000 (Default) |
1-32000 (1-32000Wh) - change in energy | ||||
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
58 | 2 | Periodic power reports | 0 | periodic reports are disabled | |
1 to 32000 (Default) |
(1-32000s) - report interval | ||||
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
59 | 2 | Periodic energy reports | 0 | periodic reports are disabled | |
1 to 32000 (Default) |
(1-32000s) - report interval | ||||
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
60 | 1 | Measuring energy consumed by the device itself | 0 (Default) |
function inactive | |
1 | function activate | ||||
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
9 | 1 | Restore state after power failure | 0 | the device does not save the state prior to the power failure and returns to „off” position | |
1 (Default) |
the device restores its state prior to the power failure |
Z-Wave Command Classes
Model: FIBARO Double Switch 2 (FGS-223)
Z-Wave Certification Number: ZC10-16075136
Supported Command Classes |
All Switch |
Application Status |
Association Group Information |
Association V2 |
Basic |
Central Scene V2 |
Configuration |
CRC16 Encapsulation |
Device Reset Local |
Firmware Update MD V3 |
Manufacturer Specific V2 |
Meter V3 |
Multi-Channel_V4 |
Multi-Channel-Association_V3 |
Notification V5 |
Powerlevel |
Protection V2 |
Security |
Switch Binary |
Version V2 |
Z-Wave Plus Info V2 |
Controlled Command Classes |
Basic |
Notification V5 |
Switch Multilevel V3 |
Z-Wave Plus: | Нет |
---|---|
Z-Wave аппаратная платформа | ZM5101 |
Z-Wave тип библиотеки | Enhanced 232 Slave |
Z-Wave тип устройства | On/Off Power Switch |
Z-Wave тип роли | Always On Slave |
Технология | Z-Wave+ |
Внутренняя/наружная установка | Внутренняя |
Производитель | Fibaro |
Группы ассоциаций | 5 |
Z-Wave Функции | Запуск сцен, Multichanel , Multichannel Association |
Максимальная нагрузка | 6.5A |
Тип диммера и выключателя | insert module |
Источник питания | Кабель AC |
Тип проводной системы | 3-Wire |
Тип вставного модуля | Relay - Double |
Функции вставных модулей | Измерение мощности |
Форм-фактор | Настенный |
Назначение | Управление освещением |
OTA обновление прошивки | Да |