Z-Wave Plus Qubino Скрытое 1 реле
Single Relay switch module to control loads up to 10A.
- Enables Z-Wave control of lights and appliances
- Monitors power consumption
- Optional Temperature Sensor
- Very small size enables modules to fit into standard switch boxes (45mm recommended)
World's smallest Flush Z-Wave Relay
FLUSH 1 RELAY
Этот модуль используется для включения и выключения различных электрических устройств, таких как конвекторы, масляные обогреватели, теплые полы, а также осветительных приборов, вентиляторов, гаражных ворот и разнообразной бытовой техники: стиральные машины, утюги, водяные нагреватели и прочее.
What is it used for?
The Qubino Flush 1 Relay is ideal for remotely controlling and switching electrical devices (e.g. lights or fans).
The smallest of them all.
The Qubino Flush 1 Relay module occupies a smaller volume than comparable modules of any other brand and will fit easily in any flush mounting box.
Energy wizard.
The Qubino Flush 1 Relay can measure the power consumption of the connected electrical device and itself has an extremely low power consumption of just 0.4 W.
Remarkably versatile.
The Qubino Flush 1 Relay can operate across a wide temperature range, from a chilly -10˚C to a scorching 40˚C (14˚–104˚F). It supports the connection of a digital temperature sensor, which is also useful for creating complex scenarios. Every module also acts as a repeater in order to improve the range and stability of the Z-Wave network.
The simplest installation.
Extremely small size and a specially designed casing mean that connecting the module inside a flush mounting box is simplicity itself. The installation process, tested and approved by professional electricians, consists of just three simple steps:
- Remove the switches from the box and disconnect the wires.
- Connect the wires to the Qubino module and insert it in the box.
- Fix the switches to the box.
Incredibly fast support. Free.
We know that when you need information you need it quickly. That is why we offer a live customer service helpline, where you can get instant answers to all your questions. Free. All our support and training is personalized and free of charge.
The most tested and most reliable module.
Qubino modules are "install-and-forget" products. Our products are made to last, so we only select and use top-quality electronic components. Our modules are also the most tested Z-Wave microcontrollers on the market. The Slovenian Institute of Quality and Metrology (SIQ), an independent testing body, tests safety parameters including temperature rise, construction, insulation resistance, power consumption and overload in accordance with the EN 60669-2-1 standard.
Technical specifications
Supported loads:
- Electric motor
- Conventional incandescent and halogen lights
- LED bulb, compact fluorescent bulb (CFL), low voltage halogen bulbs with electronic transformer
- Low voltage halogen bulbs with conventional transformer
Чем больше диапазон действия, тем более надежным является продукт - устройство имеет первоклассную антенну. Оптимизированное для надежности, это устройство может взаимодействовать беспроводным способом на расстояния более 150 метров.
Лучше антенна. Лучше Z-Wave. Устройство разработано на технологии Z-Wave Plus последнего 5го поколения, чтобы предоставить вам самое быстрое время отклика и оптимальное время жизни батареи между перезарядками.
Если вы используете устройство для обеспечения безопасности, вы хотите чтобы взаимодействие было защищенным. Вот почему устройство использует беспроводное шифрование AES-128 для защиты от несанкционированного доступа и хакеров.
Используете ли вы устройство для комфорта или безопасности, вы желаете чтобы оно всегда оставалось обновленным до последней версии. Как бы не создавались обновления прошивки для устройства, вы всегда можете обновить его с помощью Microsoft Windows или выбрать Z-Wave контроллер.
Technical Specification
- MODEL NUMBER
- ZMNHAD1
- HARDWARE
- Z-Wave Chip 500 series
- Switching: MOSFET (trailing edge)
- COMMUNICATION PROTOCOLS
- Z-Wave Plus
- FEATURES
- Support for the connection of digital temperature sensor
- Power consumption measurement
- 3 binary inputs offer the option to connect additional devices such as sensors, switches/push buttons
- LED AND BUTTONS
- LED indicator
- Include/Exclude button
- ASSOCIATION GROUP
- Eleven groups and sixteen devices (nodes)
- MAXIMUM CURRENT
- 1 X 10A / 230VAC
- 1 X 10A / 30VDC
- MAXIMUM LOAD
- 2300W (230VAC) (Resistive)
- 240W (24VDC) (Resistive)
- (Resistive-Inductive)
- (Resistive-Capacitive)
- POWER MEASUREMENT ACCURACY
- P=5-50W: +/-3W
- P>50W: +/-3%
- OVERCURRENT PROTECTION
- required external circuit breaker
- DIMENSIONS
- Package: 79 x 52 x 22 mm (LxWxH)
- Unit: 41.8 x 36.8 x 15.4 mm (LxWxH)
- CERTIFICATIONS
- FCC, Z-Wave
- POWER SUPPLY
- AC 100-240VAC, 50-60Hz
- 24–30 VDC
- POWER CONSUMPTION
- up to 0.4W
- RADIO SIGNAL POWER
- up to 1mW
- RANGE
- up to 50m (outdoors) and 40m (indoors)
- OPERATIONAL TEMPERATURE
- -10-40°C
- FOR INSTALLATION IN BOXES
- D ≥ 60mm, depth ≥ 60mm
- IP CODE
- IP20
- WEIGHT
- Net: 28 g
- Gross: 34 g
Package content
- Unit
- User manual
Z-Wave Specification
- Z-Wave Alliance
- Manufacturer
Z-Wave Association Capabilities
Model: Qubino Flush Dimmer (ZMNHDD1)
Z-Wave Certification Number: ZC10-16115319
Group ID |
Maximum Nodes |
Description |
1 | 1 | Z-Wave Plus Lifeline |
2 | 16 | Basic On/Off |
3 | 16 | Start Level Change/Stop Level Change |
4 | 16 | Multilevel Set |
5 | 16 | Basic On/Off |
6 | 16 | Notification Report |
7 | 16 | Binary Sensor |
8 | 16 | Basic On/Off |
9 | 16 | Notification Report |
10 | 16 | Binary Sensor Report |
11 | 16 | Multilevel Sensor Report |
Z-Wave Configuration Capabilities
Model: Qubino Flush Dimmer (ZMNHDD1)
Z-Wave Certification Number: ZC10-16115319
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
1 | 1 | Input 1 switch type | 0 (Default) |
Mono-stable switch type (push button) – button quick press turns between previous set Dimmer value and zero. | |
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
10 | 2 | Activate / deactivate functions ALL ON / ALL OFF | 255 (Default) |
ALL ON active, ALL OFF active. | |
0 | ALL ON is not active, ALL OFF is not active. | ||||
1 | ALL ON is not active, ALL OFF active. | ||||
2 | ALL ON active, ALL OFF is not active. | ||||
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
100 | 1 | Enable / Disable Endpoints I2 or select Notification Type and Event | 0 (Default) |
Endpoint, I2 disabled. | |
1 | Home Security; Motion Detection, unknown loc. | ||||
2 | CO; Carbon Monoxide detected, unknown loc. | ||||
3 | CO2; Carbon Dioxide detected, unknown loc. | ||||
4 | Water Alarm; Water Leak detected, unknown loc. | ||||
5 | Heat Alarm; Overheat detected, unknown loc. | ||||
6 | Smoke Alarm; Smoke detected, unknown loc. | ||||
9 | Sensor binary. | ||||
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
101 | 1 | Enable / Disable Endpoints I3 or select Notification Type and Event | 0 (Default) |
Endpoint, I3 disabled. | |
1 | Home Security; Motion Detection, unknown loc. | ||||
2 | CO; Carbon Monoxide detected, unknown loc.. | ||||
3 | CO2; Carbon Dioxide detected, unknown loc. | ||||
4 | Water Alarm; Water Leak detected, unknown loc. | ||||
5 | Heat Alarm; Overheat detected, unknown loc. | ||||
6 | Smoke Alarm; Smoke detected, unknown loc. | ||||
9 | Sensor binary. | ||||
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
11 | 2 | Automatic turning off output after set time | 0 (Default) |
Auto OFF disabled. | |
1 to 32536 | 1 second - 32536 seconds Auto OFF enabled with define time, step is 1 second. | ||||
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
110 | 2 | Temperature sensor offset settings | 32536 (Default) |
Offset is 0.0°C. | |
1 to 100 | value from 0.1°C to 10.0°C is added to actual measured temperature. | ||||
1001 to 1100 | value from -0.1°C to -10.0°C is subtracted to actual measured temperature. | ||||
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
12 | 2 | Automatic turning on output after set time | 0 (Default) |
Auto ON disabled. | |
1 to 32535 | 1 second - 32535 seconds Auto ON enabled with define time, step is 1 second. | ||||
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
120 | 1 | Temperature sensor reporting | 5 (Default) |
0,5°C change. | |
0 | Reporting disabled. | ||||
1 to 127 (Default) |
0,1°C - 12,7°C, step is 0,1°C. | ||||
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
2 | 1 | Input 2 switch type | 0 (Default) |
Mono-stable switch type (push button) – button quick press turns between previous set Dimmer value and zero. | |
1 | Bi-stable switch type. | ||||
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
20 | 1 | Enable/Disable Additional Switch | 0 (Default) |
Single push button (connected to I1). | |
1 | Additional switch (connected to I1 and I2) | ||||
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
21 | 1 | Enable/Disable Double click function | 0 (Default) |
Double click disabled. | |
1 | Double click enabled. | ||||
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
250 | 1 | Unsecure / Secure Inclusion | 0 (Default) |
Unsecure Inclusion. | |
1 | Secure Inclusion. | ||||
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
3 | 1 | Input 2 contact type | 0 (Default) |
NO (normally open) input type. | |
1 | NC (normally close) input type. | ||||
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
30 | 1 | Saving the state of the device after a power failure | 0 (Default) |
Flush Dimmer module saves its state before power failure (it returns to the last position saved before a power failure). | |
1 | Flush Dimmer module does not save the state after a power failure, it returns to "off" position. | ||||
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
4 | 1 | Input 3 contact type | 0 (Default) |
NO (normally open) input type. | |
1 | NC (normally close) input type. | ||||
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
40 | 1 | Power reporting in Watts on power change | 0 | Reporting disabled. | |
1 to 100 (Default) |
1% - 100% Reporting enabled. Power report is send (push) only when actual power in Watts in real time changes for more than set percentage comparing to previous actual power in Watts, step is 1%. | ||||
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
42 | 2 | Power reporting in Watts by time interval | 0 (Default) |
Reporting disabled. | |
1 to 32767 | 1 second - 32767 seconds. Reporting enabled. Power report is send with time interval set by entered value. | ||||
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
60 | 1 | Minimum dimming value | 1 (Default) |
1% (minimum dimming value) | |
1 to 98 (Default) |
1% - 98%, step is 1%. Minimum dimming values is set by entered value. | ||||
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
61 | 1 | Maximum dimming value | 99 (Default) |
99% (Maximum dimming value). | |
2 to 99 (Default) |
2% - 99%, step is 1%. Maximum dimming values is set by entered value. | ||||
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
65 | 2 | Dimming time (soft on/off) | 100 (Default) |
1s | |
50 to 255 (Default) |
00 mseconds - 2550 mseconds (2,55s), step is 10 mseconds. | ||||
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
66 | 2 | Dimming time when key pressed | 3 (Default) |
3s | |
1 to 255 (Default) |
1 second – 255 seconds | ||||
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
67 | 1 | Ignore start level | 0 (Default) |
Respect start level. | |
1 | Ignore start level. | ||||
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
68 | 1 | Dimming duration | 0 (Default) |
Dimming duration according to parameter 66. | |
1 to 127 | From 1 to 127 seconds. |
Z-Wave Command Classes
Model: Qubino Flush Dimmer (ZMNHDD1)
Z-Wave Certification Number: ZC10-16115319
Supported Command Classes |
All Switch |
Association Group Information V2 |
Association V2 |
Basic |
Binary Sensor |
Configuration |
Device Reset Local |
Manufacturer Specific V2 |
Meter V4 |
Multi-Channel_V4 |
Multi-Channel-Association_V3 |
Notification V5 |
Powerlevel |
Security |
Sensor Multilevel V7 |
Switch Binary |
Switch Multilevel V3 |
Version V2 |
Z-Wave Plus Info V2 |
Controlled Command Classes |
Basic |
Switch Multilevel V3 |
Z-Wave Plus: | Нет |
---|---|
Z-Wave аппаратная платформа | ZM5202 |
Z-Wave тип библиотеки | Enhanced 232 Slave |
Z-Wave тип устройства | On/Off Power Switch |
Z-Wave тип роли | Always On Slave |
Технология | Z-Wave+ |
Внутренняя/наружная установка | Внутренняя |
Производитель | Qubino |
Группы ассоциаций | 9 |
Z-Wave Функции | Multichanel , Multichannel Association |
Поддерживаемые типы выключателей/управления | Кнопочный, Тумблерный, Кулисный, Без подсветки |
Максимальная нагрузка | 10A |
Тип диммера и выключателя | insert module |
Источник питания | Кабель AC, Блок питания DC |
Тип проводной системы | 3-Wire |
Тип вставного модуля | Relay - Single |
Функции вставных модулей | Дополнительные входы, Измерение мощности, Вход для цифрового датчика температуры |
Способы нажатия | Одно нажатие |
Форм-фактор | Настенный |
Назначение | Управление освещением |
OTA обновление прошивки | Да |